The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.
MHD Flasher F + G系列是适用于宝马的完整闪光调校应用程序。与背负式模块不同,它能够完全重新映射DME,同时保留所有OEM安全机制。这样可以实现最高性能,最大安全性和无与伦比的驾驶性能。
---------------------------------------------
完全OBD闪烁:
您可以在家中安装MHD并立即开始调整!没有必要移除和发送您的DME以进行昂贵的“解锁”。只需下载通过K + DCAN电缆连接到您的Android设备和车辆的OBD-II端口的MHD Flasher F系列应用程序,启动应用程序,并在15-25分钟内完成初始安装。进一步的地图变化要快得多 - 只需1-3分钟!您可以随时将您的车辆恢复到工厂OEM闪存,无需初始备份。
---------------------------------------------
PureBoost的Stage 1,Stage 2和E85 OTS(Off The Shelf)地图:
N55 EWG(2013年7月至2013年之后用电子废气门建造的车辆):
- 第1阶段(最高360HP / 540NM)(不适用于M2和X4 M40i)
- 第2阶段(高达390HP / 580NM)
- 第2阶段(最高430HP / 630NM)
- 乙醇混合物图:第1阶段,第2阶段和第2阶段E20地图,用于20%的乙醇混合物
N55 PWG(气动废气门):
- 第1阶段(最高340HP / 540NM)
- 第2阶段(高达370HP / 580NM)
- 第2阶段(最高400HP / 630NM)
- 乙醇混合物图:第1阶段,第2阶段和第2阶段E20地图,用于20%的乙醇混合物
S55(宝马M3 / M4 F8x):
- 第1阶段(最高530HP / 700NM)
- 第2阶段(高达560HP / 780NM)
- 乙醇混合物图:第1阶段,第2阶段和第2阶段E30地图,乙醇混合物含量为30%
B58:
- 第1阶段(最高420HP / 580NM)
- 第2阶段(最高470HP / 630NM)
- 乙醇混合物地图:第1阶段,2地图,乙醇混合物为30%
---------------------------------------------
使用可配置且响应迅速的仪表布局监控您的发动机行为,确保其运行正常。 50个发动机参数一目了然!
这些是一些可用的监视器:
- 提升,提升目标
- Lambda(AFR)
- 进气温度(IAT)
- 每个气缸的点火正时
- 冷却液温度
- 油温,油压
- 传输温度
- 高压燃油泵(HPFP)
- 节气门位置
- 废气门占空比(WGDC)
- RPM
- 速度
- EGT
还有很多…
MHD独家高级显示器:
- 每个气缸的定时校正
- 提升目标EX,可读取高于22.x psi(宝马增压目标通道不能)
- Base Compressor Axis:Boost Setpoint,MAF req WGDC。
- 主动扭矩限制器
还有很多…
---------------------------------------------
这些Flash选项可以直接通过应用程序应用于任何地图:
- 排气燃烧(持续时间和侵略性,最小速度,最小转速)
- N20地图传感器(在N55上)
- 拆下最高限速器(Vmax)
- 冷启动降噪
- 在运动模式下打开排气盖
- 限制每档的功率
- XHP TCU闪存支持(优化的OTS地图)
- 运动冷却模式,增加水/空气中冷器冷却(仅限B58)
---------------------------------------------
支持的汽车:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
所有汽车都支持X-Drive。
所有性能动力套件车都支持。
查看我们的主页/用户手册,了解有关每个阶段的更多信息和建议的修改。
The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.